When is an electrical JSA template enough?

When the installation you will touch is isolated, locked out, and proved dead, and the remaining work is extra-low-risk fit-off — GPOs, lights, clipping — with no live parts in reach. That is not a licence to skip isolation.

Is the electrical JSA free?

Trial generate and PDF, no card. This Nundah office fit-off is a layout. A live café board is the other page.

SWMS or JSA for electrical work?

On or near energised installations: SWMS (HRCW). Isolated extra-low-risk fit-off: JSA. If you are not sure it is isolated, it is not a JSA job.

Licensing is state-based. Citations: WHS, or Victoria’s OHS Act 2004 and OHS Regulations 2017. The JSA does not replace an electrical licence.

What about livening at the end?

Closing a main onto a new circuit next to a live bus is often back in SWMS territory. Keep this JSA for the isolated fit-off; write the electrical SWMS for the energised part.

Electrical JSA Template Australia | Isolated Extra-Low-Risk Fit-Off

New ground-floor office. Board for this tenancy isolated by the builder’s sparkie of record. Clip, terminate GPOs, hang lights from a platform under 2 m, IR test. Energising the board later is a separate, SWMS-aware step — not hidden in this JSA.

Job / task: Isolated GPO and light fit-off — tenancy DB locked off and proved dead
Site: New ground-floor office, Nundah QLD 4012
Document: JSA · extra-low-risk isolated fit-off · example only
PPE: Hi-vis, steel-caps, glasses, gloves when pulling in, insulated tools as a habit even on proved-dead circuits

Example layout. If you cannot prove dead, or live parts remain in reach, this JSA is the wrong document — use the electrical SWMS.

Step	Hazards	Controls	5×5 risk
1. Confirm isolation, lock-out, prove dead on the conductors you will terminate Responsible: Licensed electrician	Wrong tenancy isolator — circuit still live Builder’s temporary still feeding a socket you thought was dead Other trades resetting a breaker you just tagged	Test the tester, prove dead, re-test the tester; lock and tag; keys with the person doing the work Trace the run; don’t trust the label on the DB door Tell the builder the lock stays on until you take it off	InitialL3×C5 = 15 High ResidualL2×C5 = 10 High
2. Pull and clip cables, terminate GPOs on the isolated circuits Responsible: Electrician	Cuts from plasterboard and cable Drilling into an unknown pipe in a new wall Manual handling of cable drums in a corridor	Glasses; don’t overfill the holesaw As-builts and a pipe finder; stop if you hit water Park drums; don’t roll them down stairs	InitialL3×C3 = 9 Medium ResidualL2×C2 = 4 Low
3. Hang lights from a platform under 2 m Responsible: Electrician	Fall from a makeshift stool (sprain, fracture — still not HRCW if under 2 m) Light fitting dropping during the hang If the void is higher than planned — fall greater than 2 m	Stable platform; three points of contact; no rolling chairs Second person on heavy fittings Measure the void first; if the fall would be over 2 m, stop and write a heights SWMS	InitialL3×C3 = 9 Medium ResidualL2×C2 = 4 Low
4. Insulation resistance test; leave the board locked until the energise procedure Responsible: Licensed electrician	Someone livening while you still have a tester on the circuit Recording a pass that isn’t Handover that implies the office is live when it isn’t — or the reverse	Lock stays on through IR tests Write the results on the job card Energise only under a separate switching sheet — if that step is on or near live parts, use the electrical SWMS	InitialL3×C4 = 12 High ResidualL2×C3 = 6 Medium

Electrical JSA template Australia (isolated fit-off)

Isolated fit-off vs live work

Filled example: office fit-off, Nundah QLD

Frequently asked questions

Generate an electrical JSA for isolated fit-off